Replacing Lock on uPVC Door
If you are looking to replace the lock on your door made of upvc you'll first need to remove the existing handle and screw holes. This is typically simple to do.
The next step is to find the screw that holds the barrel in place. The screw is typically different to the screws that are used in other locks, and is located on the edges of the faceplate of the lock.
Take the Cylinder off
The first step in changing a lock on your door made of upvc is to remove the existing cylinder from the door. It is a straightforward process that can take about 30 minutes. All you need is an ordinary screwdriver. You will need to find the Euro fixing screw for cylinders, which is usually in the edging on the inside of the door, right next to the lock cylinder. The screw is typically colored differently from the rest of the screws and is easy to identify. Take it off and store it in a safe location.
After removing the cylinder, you can begin removing the handle. To do this, open the door so you have full access to the edging on the inside of the door as well as the side of the faceplate of the lock.
Take off the screw that connects the handle to the door using a screwdriver. Once the screw is removed you should be in a position to pull the handle towards you, and the rest of the mechanism should be removed from the door.
If you're having difficulty getting the handle off, you may need to take off the screw that is holding it to the stud in the door frame. This can be accomplished with a drill or screwdriver, and you'll need to be careful not to cut the screw head or cross-thread it.
When you're ready to replace the cylinder, be sure it's the correct size for your door. Cylinders are measured according to two factors: (a), the distance from the center of the Fixing Screw to the bottom of the cylinder, and (b) the distance between the hole of the keyhole and edge of the lockplate.
Remove the Handle
If your upvc door handle becomes stiff or loose, the good news is that this is a relatively simple issue to repair. The cause is usually due to wear and tear with the cylinder or internal components of the multipoint lock which are located inside the door between the handle and the frame. It is not uncommon for upvc locks to become worn due to extreme weather conditions, heavy use or simply ageing and this can cause problems with the locking or closing mechanism of the door.
If the cylinder has worn, it will often be difficult to turn the key, and the lock can also become stiff, which could cause the handle to droop. This can be resolved by replacing the cylinder which is a straightforward procedure. This can be done by yourself, but you will need to have some knowledge about the mechanism's workings. You will need to remove the handle to replace the cylinder.
To accomplish this, you'll need a screwdriver as well as a tape measure. You must be aware of the size of your current cylinder because it will allow you in locating a replacement that fits correctly. The cylinder is what permits you to lock the upvc door. It is crucial to purchase an upgrade that is exactly the same size.
To take off the old cylinder, you'll have to remove the screws that secure it. Be careful not to strip the screws, as this can make it very difficult to remove them again in the future. Once the screws are removed, the cylinder should come out easily.
Take off the Lock Barrel
Upvc is a very durable material that is designed to ensure that you and your family are secure. They are available in a wide variety of colours and styles that will complement any decor. replacement locks for double glazed windows are also maintenance-free and thermally efficient. They do not come without a few disadvantages. As time passes, the locking point or barrel lock can become faulty and will require replacement. This is a simple process however there are a few important things to consider before beginning.
To access the screw holding the lock cylinder, it is have to take off your door handle. It's usually a different colour from the rest of the screws and is situated near the edge of the door, just where the keyhole is located. Remove the screw and place it somewhere safe. Slide the handles off both the inside and outside of the door. Make sure to do this slowly and not too fast, as it may harm your uPVC door.
After you have removed the handles using a screwdriver, remove the screws that attach them to the door frame. This will let you better access the pins that hold the cylinder in place. Try to pull and wiggle the cylinder in order to see if this will loosen it. Once it does, push it towards you, then pull it out of the socket.
After taking out the old lock cylinder, it is important to replace with a new one that has anti-snap protection and anti-bump. You can do this yourself if have the tools you need, or you can engage an expert locksmith to do it for you. It's a relatively simple task that should take about five minutes to complete.
Install the New Cylinder
A door lock made of upvc can be damaged or broken in many ways, for instance, a tenant might have left and not returned the key or the cylinder might have become damaged and is no longer functioning as it should. It is essential to select the correct size replacement for your door's upvc lock. If the wrong one is installed, your upvc doors may be more vulnerable to the 'lock snapping technique which is the reason for 25 percent of burglaries.
It is important to install the correct cylinder. The procedure is simple and takes only five minutes. To swap the cylinder and handle faceplate, you will need to remove the screws that are attached to them.
Before you get started, make sure that the handle is opened and that you have full access to the inside edge of the door as well as the side of the handle faceplate that holds the lock cylinder. This will ensure that you can easily disconnect the lock cylinder, without needing to move the handle on the door to expose any internal parts of the handle frame.
The next step is to remove the old cylinder and measure it, you will need to know the overall length and the diameter of the cylinder, which rotates to lock and unlock the door. This will help you find a new cylinder that is the same or smaller. This is the most important part of the entire process. The cylinder should be flush with the handle and not protrude more than 5mm beyond it.
Install the Handle
A upvc lock can be jammed if there is a break in the case that controls the bolts that retract into the strike or keep plate. This can often be resolved by adjusting the Allan key under the hinges. However, this could occasionally cause excessive stress on the components within the centre casing and it is recommended to call in a professional.
During the changing process it is important to have easy and quick access to both sides of the handle, as well as having the appropriate tools. It is recommended also to prop the door up to ensure that it doesn't close during this process.
The first step is to loosen the screws that hold the handle in place using a screwdriver. Once these are loosened the handle can be removed. After removing the cylinder and the handle, it's now time to put in the new handle. Make sure the new handle is the right size for your existing cylinder and hole center. Examine the length of the spindle on the lever you are currently using to determine this. Also, ensure that the screw fix centres on the handle are the same as the screw fixing centres on your existing hole centre and cylinder.
The replacement handles offered by Fab and Fixed are available in a wide range of styles and are made to last. They are ideal for those who want to upgrade their Upvc handles and enhance their home security. Having the right handle will ensure that your house is secure and safe, and will not be easy for thieves to break into.